Shock a Billy 1995 on pivot hardware

Rick Draper · March 5th, 2013, 9:44 AM

Can anyone tell me who produced the original pivot hardware for the last Shock a Billys? I am trying to track some bits down. I think it could be a futile task though.

webby · March 6th, 2013, 8:51 AM

Have you tried contacting Wendyl, can't think of anybody else who would have any.

Rick Draper · March 8th, 2013, 8:30 AM

Yep I have tried Wendyll, this place is literally my last throw of the dice.

tvcreative · March 8th, 2013, 10:10 AM

time to be creative and see a machine shop

webby · March 11th, 2013, 3:58 AM

Have you not heard back from her or does she just not have any?

Rick Draper · March 11th, 2013, 10:02 AM

Wendyll let me know she had none of them.

I think if i search enough I will find them, I have managed to source new bushings for the prototype frame I have so I think I might be able to discover who the bushes came from for the later version.

Rick Draper · March 11th, 2013, 5:04 PM

Small update. I contacted Serrotta bikes and they said to try McMaster Carr, I have found the grooved O-ring seals used and I just need to measure the size and hopefully I will find the bushings too. Sadly the site is a load of pap and I am locked out for 24hr's as I have viewed too many products

Rick Draper · March 20th, 2013, 7:09 AM

I believe I have found out where the original hardware came from. The only slight problem is they wont supply outside of America!

If any American members can help me out I will make it worth there while. They are based in Santa Fe Springs, CA.

March 5th, 2013, 9:44 AM	#1
Rick Draper Member Join Date: June 13th, 2011 Location: Macclesfield Posts: 58	Shock a Billy 1995 on pivot hardware Can anyone tell me who produced the original pivot hardware for the last Shock a Billys? I am trying to track some bits down. I think it could be a futile task though.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

March 6th, 2013, 8:51 AM	#2
webby Member Join Date: July 16th, 2004 Location: Stoke, GB Posts: 37	Have you tried contacting Wendyl, can't think of anybody else who would have any.

March 8th, 2013, 8:30 AM	#3
Rick Draper Member Join Date: June 13th, 2011 Location: Macclesfield Posts: 58	Yep I have tried Wendyll, this place is literally my last throw of the dice.

March 8th, 2013, 10:10 AM	#4
tvcreative Senior Member Join Date: March 15th, 2010 Location: Naperville IL Posts: 716	time to be creative and see a machine shop

March 11th, 2013, 3:58 AM	#5
webby Member Join Date: July 16th, 2004 Location: Stoke, GB Posts: 37	Have you not heard back from her or does she just not have any?

March 11th, 2013, 10:02 AM	#6
Rick Draper Member Join Date: June 13th, 2011 Location: Macclesfield Posts: 58	Wendyll let me know she had none of them. I think if i search enough I will find them, I have managed to source new bushings for the prototype frame I have so I think I might be able to discover who the bushes came from for the later version.

March 11th, 2013, 5:04 PM	#7
Rick Draper Member Join Date: June 13th, 2011 Location: Macclesfield Posts: 58	Small update. I contacted Serrotta bikes and they said to try McMaster Carr, I have found the grooved O-ring seals used and I just need to measure the size and hopefully I will find the bushings too. Sadly the site is a load of pap and I am locked out for 24hr's as I have viewed too many products

March 20th, 2013, 7:09 AM	#8
Rick Draper Member Join Date: June 13th, 2011 Location: Macclesfield Posts: 58	I believe I have found out where the original hardware came from. The only slight problem is they wont supply outside of America! If any American members can help me out I will make it worth there while. They are based in Santa Fe Springs, CA.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)